How Do I Start My Sprinklers After Winter?
Wait until the ground has thawed and hard freezes are no longer in the forecast. Then inspect the system, close the drain and test valves, and open the main shutoff valve slowly. Run each zone by hand and fix any leaks, clogged heads or misaimed spray before you set the timer.
What winterization and a sprinkler blowout mean
Sprinkler winterization is the work done in fall to protect your system from freezing. Water left in pipes, valves and heads expands as it freezes and can crack fittings, split pipe and break spray heads.
A sprinkler blowout is the most common way to do it. Compressed air is pushed through each zone to force the remaining water out of the lines. Some systems also use manual drain valves to let water run out. Either way, the goal is a system that is empty when the cold arrives.
Starting up in spring is the reverse. You close the drains, refill the pipes slowly and check everything for damage that frost may have caused.
Pick the right time to start
Timing matters more than most people think. If you turn the water on too early, a late freeze can burst pipes that are now full of water. Wait until the soil has thawed and overnight lows stay above freezing. Local frost dates vary, so check your area's typical last-frost timing or ask a local irrigation company.
If you live somewhere with unpredictable spring weather, it is fine to wait an extra week or two. Lawns rarely need much irrigation in early spring anyway, because the ground is still damp from snowmelt and rain.
Inspect before you open any valves
A quick walk around the yard can save you from a flooded flower bed. Look for anything that frost, mowers or snow removal may have damaged.
Check these items first:
- Spray heads that are cracked, tilted or sunk below the grass line
- Wet or sunken spots in the lawn that could point to a buried pipe issue
- Exposed pipe, valve boxes with broken lids, or boxes full of soil or water
- The vacuum breaker or backflow preventer for cracks, especially if it sits above ground
- The controller for dead batteries, loose wires or a blank display
Step-by-step startup for an in-ground system
The exact layout depends on your setup, but most residential systems follow the same order. Go slowly. Opening water too fast is the main cause of damage during startup.
Follow these steps:
- Turn the controller to off or rain mode so no zone starts on its own.
- Close any manual drain valves and the small test cocks on the backflow preventer or vacuum breaker, if your system has them. Handle levers should sit crosswise to the pipe when closed.
- Find the main shutoff valve, often in a basement, crawl space, garage or a valve box outside.
- Open the main valve a little at a time. Let the pipes fill gradually. A sudden surge can cause water hammer, which stresses fittings.
- Once the water is flowing steadily, open the valve fully.
- Check the backflow device and exposed pipes for leaks or spraying.
- Set the controller to manual and run one zone at a time, starting with zone one.
- Walk each zone while it runs and note anything that looks wrong.
- Set the clock, schedule and seasonal adjustment, then switch the controller back to auto.
Run each zone and fix common problems
Running zones by hand is where you find what winter did. Give each zone a minute or two to build pressure before you judge it. Heads often spit air and sputter at first, which is normal.
Use this table to match what you see with a likely cause.
| What you see | Likely cause | What to do |
|---|---|---|
| Weak or uneven spray | Clogged nozzle or filter, or a partly closed valve | Clean the nozzle and filter, and confirm valves are fully open |
| Head will not pop up | Debris, damage or low pressure in the zone | Dig around the head, clean it and replace it if cracked |
| Water pooling or geyser | Broken head or pipe | Shut the zone off and repair or replace the part |
| Spray hits pavement | Head tilted or sunk | Reset the aim and raise or straighten the head |
| Zone will not turn on | Wiring, solenoid or controller issue | Check connections and test the controller before replacing parts |
If you use hose-end sprinklers instead
Not every yard has buried pipes. If you water with a sprinkler that attaches to a garden hose, spring startup is simpler. Check the hose and washers for cracks, then connect it and run it briefly to flush out dirt and spider webs before you set it on the lawn.
Look at the nozzles too. Mineral buildup and debris can block them over winter. Some models help with this: the Eden 96213 includes a built-in nozzle cleaning tool, and the Melnor MiniMax Turbo lists a dirt-resistant drive meant to keep running smoothly, even with well water.
If a sprinkler did not survive the cold, our best sprinkler comparison puts coverage, type and adjustments on one spec sheet. Coverage figures there run from 3,315 to 6,360 sq ft among the models that list it, so measure your lawn first and choose a number above it. You can also read how oscillating, gear-drive and impact types differ in our sprinkler comparison before you decide what suits your yard shape.
Safety notes
Most startup work is low risk, but a few points deserve care.
Wear safety glasses when you clear nozzles or work near pressurized heads, because debris can shoot out. Keep your face away from the backflow device when you open valves. If a pipe or fitting looks damaged, shut off the water before you reach in.
Turn off power to the controller before you touch wiring, and keep tools and wet hands away from live connections. If you use compressed air for any reason, do not exceed the pressure your system's maker allows, and leave blowouts to a trained pro if you are unsure. Gas shutoffs and water heaters in the same utility space are not part of this job, so leave them alone.
Frequently asked questions
How do I know the system is safe to turn on?
Check that the soil has thawed and that the forecast shows no hard freezes. Inspect for visible damage first. If you find cracked parts, repair them before you add water.
Why do my heads sputter when I start a zone?
Air trapped in the pipes escapes through the heads as the lines fill. It should clear within a minute or two. If it keeps sputtering, look for a leak or a clogged nozzle.
Do I need a pro for startup?
Many homeowners handle it themselves if the system is simple. A pro makes sense if you have a complex layout, find a leak you cannot trace, or your backflow device needs testing that your area requires.
Should I water right after startup?
Only as needed. Run a short manual cycle to test each zone, then set a schedule that matches the weather and your lawn's needs, since spring grass often needs less water than summer grass.
Melnor 65167AMZBest overall
Melnor 65131AMZBest for linking sprinklers
Orbit 58573NLightest in the lineup