Guide

Can You Weld a Magnet? What Happens and Why

You can physically weld on a magnet, but you should not. The heat of the arc weakens or erases its pull, and the magnet's field can push the arc off course. To attach a magnet or hold work in place, use fasteners, adhesive, or a purpose-built welding magnet kept clear of the arc.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best welding magnets comparison

What happens when you weld a magnet

Welding puts a lot of heat into a small spot. A permanent magnet depends on tiny internal regions staying lined up in the same direction. Heat shakes them out of line, and when the metal cools they do not snap back. You end up with a weaker magnet, or one that no longer holds at all.

Several things usually happen together, and the first one is the one people notice.

  • Loss of strength: the magnet holds far less, or nothing, once it cools.
  • Arc blow: leftover magnetic fields can bend the arc away from the joint.
  • Physical damage: platings burn off and brittle magnet material can crack.
  • Fumes: burning coatings, such as plating on small magnets, can create fumes you should not breathe.

Why heat ruins a magnet

Every magnetic material has a temperature above which it stops behaving like a magnet. Past that point the internal alignment is gone. A welding arc is far hotter than any of these limits, so the part of the magnet near the weld is wiped out almost instantly.

The damage does not stop at the hot spot. Heat spreads through the body, and some magnet types start to lose strength well before they get hot enough to glow. Welding current can also disturb a magnet's alignment on its own, which is why even a careful weld close by can leave it weaker.

Arc blow and why nearby magnets matter

Arc blow happens when a magnetic field pushes on the welding arc. The arc wanders, spatter increases and the bead can come out uneven or poorly fused. A magnet sitting on or near the joint is one possible cause, and a magnetized workpiece is another.

If your arc starts acting strangely, remove loose magnets from the area first. Then try moving the ground clamp, changing your welding direction, or shortening the arc. Work that has been lifted with a magnetic crane or clamped to a strong magnet may need demagnetizing.

Can you weld a magnet to steel or metal?

Most people asking this want a magnet fixed permanently to a steel part. Welding is the wrong tool for that job because it destroys the thing you are trying to attach. The smarter plan is to weld the steel and add the magnet afterward, or to skip heat entirely.

Here is how the common options compare.

MethodBest forNotes
Weld the magnet directlyAlmost nothingHeat ruins the pull and may crack the magnet
Weld a steel tab or cup, add the magnet laterFixtures built from steelLet the weld cool fully before the magnet goes near it
Screws or boltsMagnets with mounting holesNo heat involved, easy to replace
Epoxy or structural adhesiveFlat magnets on clean surfacesClean both faces and follow the cure time
Magnet with threaded stud or steel cupMounting to bracketsThread or bolt it on after all welding is done

Neodymium magnets need extra care

Neodymium magnets are very strong for their size, but they are also brittle and sensitive to heat. A thin plating protects them, and welding or grinding next to it can strip that layer. Heat will weaken them far sooner than it would a ferrite magnet.

Fasten them with adhesive, a mounting hole or a retaining pocket instead. Fine dust from cutting or grinding these magnets can ignite, so avoid shaping them with power tools. Large ones can also snap together and pinch skin hard, so handle them slowly and keep them apart.

Use welding magnets the right way

Welding magnets are made for this job. They hold two pieces at a set angle so you can tack them without extra hands. You weld the workpiece, not the magnet, and you keep the arc off the magnet body.

Our best welding magnets page lists five options with holding force from 25 lb up to 77 lb and packs of one to six magnets. The TOOLIOM listing even advises against welding directly next to the magnet body or exposing it to excessive heat. If you need odd angles, the adjustable model there covers 20 to 200 degrees, while fixed arrow sets cover common corners faster.

A simple routine protects both your work and your magnets:

  • Clean rust and scale from the contact points so the magnet sits flat.
  • Set the angle, seat both pieces firmly and check the fit before striking an arc.
  • Place the magnet so the weld is a good distance from its body.
  • Tack the joint in a few spots, then move or remove the magnets before the full weld.
  • Let hot work cool before touching it, and keep magnets off hot metal.

Safety notes

Wear a welding helmet with the right shade, safety glasses under it, and gloves. Sparks and spatter can reach a magnet and the area around it, so keep your hands clear of the arc when you adjust a setup.

Work with good ventilation, especially if a magnet has plating or a coating that could burn. Strong magnets can interfere with pacemakers and other implanted medical devices, so anyone with one should stay away from them and ask a doctor. Also unplug equipment before you change cables or clamps, and keep magnets away from phones and cards.

Quick takeaway

Do not weld a magnet. Weld the steel, keep magnets away from the arc, and use a welding magnet designed for positioning when you need to hold angles. For more on picking one, see our welding magnet comparison and match the holding force to your stock.

Frequently asked questions

Do welding magnets work on stainless steel?

It depends on the grade. Welding magnets grip ferrous metals, and many common stainless grades are not magnetic enough to hold. Check that your workpiece is attracted to a magnet before you plan a setup around it.

How do I demagnetize a workpiece before welding?

A magnetized part can cause arc blow. Common fixes are moving the ground clamp, welding toward the strongest part of the field, or using a demagnetizing coil if you have access to one. Removing nearby magnets and heavy cables carrying current can also help.

Can a magnet that got too hot be recharged?

Sometimes. If heat only weakened it and did not damage the material, a strong magnetizing device can restore part of its pull. Past its limit, though, the loss is permanent. Most hobbyists do not own magnetizers, so replacing the magnet is more practical.

Do all magnets lose strength at the same temperature?

No. Magnet types differ. Neodymium is among the most heat-sensitive common types, while ferrite and alnico tolerate more. None of them survive a welding arc, so the safe habit is the same for every type: keep the heat away.

Compare the products