Guide

Can You Use a Thickness Planer as a Jointer?

Partly. A thickness planer can stand in for a jointer on one job, flattening a board face, if you ride the board on a flat sled and shim it so it cannot flex. It cannot replace a jointer for squaring edges, and it will not flatten a warped board on its own.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best thickness planer comparison

Why a planer cannot flatten a board on its own

A jointer and a planer do different jobs. A jointer registers a board against a flat table, so the cutterhead removes high spots and leaves one truly flat face. A planer sets the second face parallel to the first, so its job is consistent thickness.

Inside a planer, feed rollers press the board down against the bed as it passes under the cutterhead. A cupped, bowed or twisted board is pushed flat under that pressure, gets cut flat, and then springs back to its old shape when it exits. You end up with a thinner board that is still warped.

That is why most woodworkers treat the two machines as a team. The jointer makes the first flat face and a square edge. The planer then brings the other face parallel and the board to final thickness. If you do not own a jointer, you need another way to make that first flat reference.

The sled method: how a planer can flatten one face

The common workaround is a planer sled, also called a planing carrier. It is a flat, rigid board, often a piece of MDF or melamine-faced panel, that rides through the planer with your workpiece fixed on top. Because the sled is flat, the rollers press on the sled, not on the board's curve.

You support the high and low spots of the workpiece with shims so it cannot rock or flex. The planer then shaves only the high spots. Once the top face is flat, you remove the board from the sled, flip it, and plane the second face directly against the bed. The two faces are now flat and parallel.

  • Use a sled that is flat, stiff and a little wider and longer than your workpiece.
  • Add a front stop so the cutterhead does not push the board forward off the sled.
  • Shim under any gap so the board does not rock when you press a corner.
  • Fix the board with hot glue, double-sided tape or screws in waste areas, not with anything the cutter can reach.
  • Take light passes, since heavy cuts can make a shimmed board shift.

Step by step: flattening a face with a planer

Check the board first. Lay it on a known flat surface and see where it rocks. Mark the high spots with chalk, which also shows you when the cut has reached them.

  • Set the sled on a flat surface and place the board on it, with the concave side down.
  • Slide thin shims under the gaps until pressing any corner does not rock the board.
  • Secure the board and shims so nothing can move during the cut.
  • Set a very shallow depth of cut and feed the sled through the planer.
  • Check the chalk marks and keep taking light passes until the top face is flat from end to end.
  • Remove the board, flip it, and plane the second face directly on the planer bed until it reaches the thickness you want.

What a planer still cannot do: edges

A planer has no way to square an edge. Its bed is a narrow platform, and a board stood on its edge is tall and unsupported. Running a board on edge through a planer is unsafe because it can tip, twist or kick back, so please do not try it.

For straight, square edges you need another tool. A jointer is designed for exactly this task, using a fence set at 90 degrees. Without one, you can rip a straight edge on a table saw using a straight-line jig, trim it with a router against a straight guide, or take it down with a hand plane. All of these work, but each needs its own setup.

Short or very thin boards are also a poor match for planer-based flattening. Machines have minimum board lengths. For example, the Jet 20 in model lists a 6-3/4 in minimum board length, so check your own planer's manual before feeding short stock.

Your options compared

Which route makes sense depends on how often you start with rough or warped lumber, and how wide it is. This table sums up the trade-offs.

MethodFlattens a faceSquares an edgeMain drawback
Planer with a sledYesNoSlow setup for each board
JointerYes, within its widthYesAnother machine and more space
Hand planesYesYesTakes skill and time
Table saw or router jigNoYes, for edgesDoes not flatten faces
Buying pre-surfaced lumberAlready flatOften already straightLess choice of boards

What to look for if your planer will do double duty

If you plan to use a sled regularly, the planer itself matters. Width is the first check. Most benchtop models on our best thickness planer page plane 13 in wide and 6 in thick, and a sled plus a board has to fit under the cutterhead. Remember that the sled's thickness uses up part of that 6 in height, so your widest and thickest boards leave less room.

Cutterhead type affects how clean the cut is on twisted or figured grain. Spiral heads, like the 26-insert cutterheads on the Cutech 40800H and WEN PL1337, use many small staggered cutters. The makers say this reduces tearout. Both list a 16 fpm low feed speed, which suits fine finishing passes. The DEWALT DW735 uses a three-knife head instead, which its listing describes as faster to change.

Snipe matters more with a sled, since the dip at the board's ends can show up on the carrier. Cutech credits four lead screws for snipe reduction, and the DEWALT DW734 lists a four-column carriage lock. If you decide you do a lot of rough stock, it may be easier to add a dedicated machine. Our best jointer page puts those options side by side, and the best thickness planer for the money page can help if you are choosing a planer first.

Safety notes

Planers throw chips and make a lot of noise, so wear safety glasses and hearing protection every time. Add a dust mask or connect a vacuum to the dust port, since fine dust builds up quickly when you plane for a while.

Unplug the machine before you change knives or inserts, adjust anything near the cutterhead, or clear a jam. Never reach into the infeed or outfeed with your hands while the cutterhead is spinning.

Check boards for nails, screws and grit before they go in, since metal can damage the cutters and throw fragments. Stand to the side of the feed path, not directly behind the board, and follow the minimum length and depth of cut in your planer's manual.

Frequently asked questions

Can a planer make a board perfectly flat without a sled?

Not reliably. The rollers flatten the board temporarily, so a warped board often springs back after the cut. A sled or a jointer gives you a true flat reference.

What should I make a planer sled from?

Pick a flat, stiff panel such as MDF or melamine-faced board. It must stay flat under load, since any curve in the sled is copied into your workpiece.

Is it safe to plane a short board?

Only if it meets the minimum length for your machine. Very short pieces can tip or jam, so check the manual or glue them to a longer carrier.

Do I need a jointer if I buy rough lumber often?

A jointer makes that work faster and gives you square edges too. If you only do it occasionally, a sled and a table saw edge jig can cover the gap.

Compare the products