Guide

Can You Replace Cabinet Hinges With Soft Close Hinges?

Yes, in most cases you can replace your current cabinet hinges with soft close hinges, and it is a manageable DIY job. The key is matching the new hinge to your door's overlay, the type of hinge you have now, and the existing screw holes and cup size. If those match, the swap takes a few minutes per door with a screwdriver.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best cabinet hinges comparison

Why the swap usually works

A soft close hinge does the same job as a regular hinge, with one addition. A small damper slows the last part of the swing so the door settles shut instead of slamming. That damper sits inside the hinge body, so you do not need to change the door or the cabinet box.

The catch is that the new hinge has to fit what is already there. If it lines up with your door and your drilled holes, the project is simple. If it does not, you may end up drilling new holes or dealing with gaps, and that is where most people run into trouble.

Our best cabinet hinges page puts several options on one spec sheet, which helps when you are comparing overlay, cup size and screw spacing before you order.

Check what kind of hinges you have now

Open a door and look at the hinge. Most cabinets use one of two styles, and the style tells you how easy the swap will be.

Concealed hinges (often called European hinges) sit in a round cup drilled into the back of the door. You see only a small arm when the door is open. These are the easiest to upgrade, because soft close versions use the same cup and a similar mounting plate.

Surface mount or semi-concealed hinges show their leaves on the face of the door or frame. Upgrading these to concealed soft close hinges is a bigger job, since the door needs a new cup hole. If you want to keep the same look and avoid drilling, look for a surface mount hinge with built-in dampers. One model on our comparison page is a surface mount, self-closing hinge with silicone dampers, but note that its listing describes it as self-closing rather than labeling it soft close, so read the wording on any hinge you consider.

Match overlay, cup size and screw spacing

Three measurements decide whether a hinge fits without extra work.

Overlay is how far the closed door covers the cabinet frame. The top five picks on our comparison page are all 1/2 inch overlay. Full overlay hinges are a different style, so measure your door and frame before you order. A wrong overlay leaves uneven gaps or keeps the door from closing fully.

Cup size is the diameter of the round hole in the door. Four of the concealed models on our page list a 35 mm cup, and one lists 30 mm. Screw hole spacing on the listed models runs from 32 mm to 48 mm, so compare that number with the holes on your cabinet. Matching these lets the new hinge sit flush without drilling.

  • Overlay: measure how much of the frame the closed door covers.
  • Cup size: measure the diameter of the round hole in the back of the door.
  • Screw spacing: measure from the center of one mounting screw hole to the other on the plate.
  • Cabinet style: face frame or frameless, since some hinges list only one.

Which situation are you in?

This table shows the most common cases and the usual way to handle each.

The reasoning is simple: the closer your new hinge matches the old one, the less work you do.

Your current hingeBest soft close routeExtra work
Concealed, 35 mm cup, matching overlaySwap for a concealed soft close hinge with the same overlayUsually none
Concealed, different overlayChoose a hinge made for your overlayMeasure carefully first
Concealed, 30 mm cupPick a hinge that lists a 30 mm cupFewer options to choose from
Surface mount or semi-concealedUse a surface mount hinge with dampers, or convert to concealedConversion needs new cup holes
Corner cabinet or lazy Susan doorUse a hinge made for cornersCheck the opening angle

How to replace the hinges, step by step

Work on one door at a time so you always have a reference for how the others are set up.

Take your time with the first door. The rest go faster once you know how the hinge clips on and adjusts.

  • Remove the door by releasing the clip or unscrewing the hinge arm from the mounting plate. Have a helper hold the door if it is large.
  • Unscrew the old hinges from the door and the cabinet.
  • Clean the holes. Scrape out old paint and debris so the new hinge sits flat.
  • Set the new hinge into the cup and drive in the screws by hand or with a drill on a low clutch setting.
  • Attach the mounting plate to the cabinet, then clip the door on.
  • Adjust the hinge. Models with 3-way or 6-way adjustment let you move the door up and down, in and out, and side to side until the gaps are even.
  • Close the door slowly and watch the last stretch of travel. It should slow and settle without a bang.

If your old screw holes are stripped

Old holes in particleboard sometimes strip out. A common fix is to glue in a wooden toothpick or dowel, let it dry, and then drive the screw in again. Some hinge kits include plastic dowels or self-tapping wooden screws, so check what your pack contains.

Power tools can overtighten screws and crack the door edge. A low torque setting helps, and so does finishing the last turns by hand.

Safety notes

If you use a drill or a bit to make new holes, wear safety glasses, because wood chips and dust can reach your eyes. Keep fingers clear of the hinge arm and the door edge while you adjust, since a damper does not stop a hinge from pinching.

Use a stable step stool for upper cabinets, and do not stretch from a chair. Remove heavy doors with a second person so they do not drop on you or the floor. If you are working near wiring or under-cabinet lighting, switch off the power at the breaker first.

What about cost?

We do not list prices on Comparabo, so we cannot give you a figure. What you can compare is pack size. The products on our page range from a 2-pack up to a pack of 60 hinges, so buy only what your doors need, plus a few spares. A standard cabinet door often uses two hinges, and tall doors may need more.

Ordering a small pack first to check the fit is a sensible move if you are unsure about overlay or cup size.

Frequently asked questions

Do soft close hinges work on any cabinet door?

Not always. The door must suit the hinge's overlay and have room for its cup. Very heavy or very tall doors may need extra hinges.

Do I have to replace every hinge on the door?

Yes, replace all hinges on a door together. Mixing old and new hinges can make the door hang unevenly and close unevenly.

Can I fix a slamming door without replacing the hinge?

Yes. Stick-on bumpers or add-on dampers can quiet a door, though they usually do not work as smoothly as a built-in soft close hinge.

Why does my new door not sit flat after swapping?

Use the adjustment screws on the hinge. If the gap stays uneven, recheck the overlay and make sure the mounting plate is seated flush.

Compare the products