Best Screw Gun for Drywall in 2027

The Funnywhale iScrewgun1017 leads our Best Score at 83, and two numbers explain most of that. Its brushless motor reaches 5000 RPM, twice the 2500 RPM of every Senco here, and it weighs 4.41 lb, the lightest gun on the page. For ceiling boards, less weight in your hand matters more than almost any other spec.

It is a 2-in-1 tool. You can drive single screws by hand or clip on the magazine for collated strips on long runs. Screw length is set without tools using marked stops, and the listing describes a depth adjustment for consistent seating, which is what keeps drywall screws from breaking the paper face.

It runs on Makita 18V batteries, and the kit includes an 18V 4.0Ah battery, a charger and a bag. The head rotates 360 degrees for corners and tight spots. The maker does not publish a warranty, so check that before you buy.

The Senco DuraSpin DS342-AC ranks second with a Best Score of 60. It is a corded auto-feed screwdriver, so there is no battery to swap halfway through a ceiling. The motor tops out at 2500 RPM, which is a normal working speed for collated drywall screws, and it handles screws from 1 to 3 in long.

Senco's patented corner-fit feed system gives you a clearer view of the screw and better reach into inside corners. Screw length changes without tools, and the patented screw-strip guide is designed to prevent misfeeds and make reloading quick. On a crew job, fewer jams means fewer stops.

At 6.68 lb it is heavier than the Funnywhale, which you will feel when driving overhead for hours. In return you get a 5-year warranty, among the longest of the models that list one, and a cord that never runs flat.

Ranked third with a Best Score of 59, the Senco DuraSpin DS322-18V brings Senco's auto-feed design to a cordless tool. It drives #6 to #12 collated screws from 1 to 3 in long, and its brushless motor runs at 2500 RPM, with a selectable 1600 rpm setting for heavy steel work.

The feed system comes off the body to expose the bit, which makes backing out a bad screw easier. It uses the same patented corner-fit feed as the corded models, plus a feed-on-return drive that lines up the next screw with the bit before you drive, for faster and more even seating.

It weighs 5.68 lb, lighter than the corded Sencos but heavier than the Funnywhale. Battery energy is listed at 72 Wh, the same as the Funnywhale kit. The 5-year warranty is a strong point for a cordless tool.

The Senco DuraSpin DS532-AC sits fourth with a Best Score of 56. It is a stand-up auto-feed model, so you drive screws while standing rather than kneeling. That suits subfloor work and the bottom rows of wall board more than ceilings. Our spec sheet records its speed at 2500 RPM, while the listing describes a 0 to 4,000 RPM motor, so check the exact figure with Senco.

Like the other Sencos, it uses feed-on-return, a sliding screw guide to prevent binding, and the corner-fit feed system for a clearer view at corners. A quick-release clamp makes bit changes fast. Screw length runs from 1 to 3 in.

At 7 lb it is the heaviest gun on the page, which makes sense for a stand-up tool but rules it out for overhead work. It carries Senco's 5-year warranty.

Fifth on our Best Score at 48, the Senco DS232-AC is a corded auto-feed screwdriver rated at 2500 rpm. It weighs 5.8 lb, lighter than the other corded Sencos here, which makes it easier to hold for upper rows of board.

It offers tool-free screw length adjustment and depth-of-drive adjustment with a depth lock, so once you set screws just below the paper face they stay that way. A variable speed trigger with lock and reverse gives control when you need to back a screw out. The belt hook can be switched for right or left hand use.

The box includes two drive bits, a drywall nosepiece, a wood nosepiece and a storage bag, so it can also handle deck screws. The listing does not give a screw length range or a warranty term, which is why it scores lower here.