Best Jigsaw Blades in 2027

The Diablo DJT128BHM leads our Best Score at 76. It is a carbide-tipped blade made for laminate and melamine, the materials that chip most easily. Diablo says it can last up to 50X longer than standard jigsaw blades, which matters because carbide blades cost more per blade than steel ones.

Its teeth are bi-directional, designed to give clean finishes on both the top and bottom of the cut. That is useful for countertops and shelving where both faces show. The 14 TPI tooth count balances speed and finish, and the 3.625 in length suits most sheet material.

A Perma-SHIELD non-stick coating reduces heat, friction and pitch buildup, so the blade cuts more freely and stays cleaner. It uses a T-shank, which fits all combo and most U-shank saws according to Diablo. The catch is the pack count: you get 1 blade, the fewest here.

Second with a Best Score of 69, the Bosch T128BHM3 is a close rival to the Diablo. It is also carbide, at 14 TPI and 3.62 in long, and made for high-pressure laminates and laminate flooring. Bosch says its carbide brazing gives 10x the life of standard bi-metal blades.

The tooth design is built to cut cleanly on both sides of brittle materials, so floor planks and laminate panels finish without chipped edges. A thin kerf removes less material, which reduces heat and helps the blade cut faster with less effort.

You get 3 blades in the pack, more than the single Diablo. Bosch does not list a non-stick coating in our data. If you are laying a laminate floor and need several straight and notch cuts, a 3-pack of carbide blades should see the job through.

The Diablo DJT102BF5 ranks third with a Best Score of 65. It solves a common problem: plastic sheets like plexiglass, acrylic and polycarbonate tend to melt and gum up a blade. Diablo designed this bi-metal blade to stay cool and make smooth, melt-free cuts.

It has 13 TPI, a tooth count suited to plastics, and a 3.625 in length. Diablo says the hardened cutting edge gives up to 5X longer blade life than standard bi-metal blades, and the non-stick coating helps keep plastic from sticking to the teeth.

The pack holds 5 blades, which is generous for a specialty blade. Like the other Diablo, it uses a T-shank that fits all combo and most U-shank saws, corded or cordless. If you cut acrylic signs, guards or panels, this is the specialist to reach for.

The DEWALT DW3741C completes our top five with a Best Score of 57. It is a 10-piece set with a case, mixing bi-metal and HCS blades in three tooth counts: 6, 10 and 18 TPI. That spread covers fast cuts in wood, cleaner cuts in wood and composites, and fine cuts in metal.

This is the set to buy if you are new to jigsaws and do not know yet which blades you will need. Coarse 6 TPI blades rip through lumber, 10 TPI is a good middle ground, and 18 TPI handles thin metal and tubing. The case keeps the blades organised and stops teeth from getting damaged in a toolbox.

All blades are T-shank. The listing does not give individual blade lengths, and the set is not specialised for laminate or plastics, where the carbide and plexiglass blades above do better.

Fourth on our Best Score at 58, the JMD JT101BR-30 is all about quantity. You get 30 blades, the most per pack on this page, which makes it a good value set for anyone who goes through blades quickly on DIY and renovation work.

These are reverse-tooth blades, which cut on the downstroke. That pushes splinters into the board instead of lifting them, so the top surface stays clean. That is the face you see when cutting laminate-faced boards, plywood or worktops from above. They are 4 in long with 10 TPI and made from thick gauge chrome-vanadium steel.

JMD lists wood, plastic, laminate, OSB and particle board as suitable materials, and says the T-shank fits most current saws, naming Milwaukee among others. Blade material quality is described rather than specified, so treat these as good workhorse blades rather than premium ones.