Drive Shaft Removal Tools · 6 compared side by side

Best Drive Shaft Removal Tools in 2027

The best drive shaft removal tool is the one that fits your vehicle and pulls the shaft without harming the seal or splines. Check three things first: whether a slide hammer is included, the fork opening size, and how many vehicles the tool fits. Some products here are full kits. Others are single adapters or pry tools. We put 6 products on one spec sheet so you can compare them side by side.

Quick answer

  • Best overall: DPTOOL L9110 (#1, Best Score 84; tool type Multi-tool set, pieces included 18 pc)
  • Extension rod included: Yuesstloo GJ-134 (#2, Best Score 79; tool type Multi-tool set, pieces included 11 pc)
  • Pry option for FWD: Bonbo VOL358 (#3, Best Score 46; tool type Popper or pry tool, pieces included 2 pc)

Ranked from 6 drive shaft removal tools that met our standard, compared on Slide hammer included, fork opening max, vehicle fit.

Updated November 202615 reviewed · 6 met our standard13 specs comparedBy Comparabo editors

As an Amazon Associate I earn from qualifying purchases. Links to retailers on this site are affiliate links; we may earn a commission at no extra cost to you.

Top picks

Best overall
#1
DPTOOL L9110

DPTOOL L9110DPTOOL CV Axle Puller Slide Hammer Kit

An 18-piece set with a 10.5 lb slide hammer, 48 mm and 63 mm forks, and a case.

Tool type
Multi-tool set
Pieces included
18 pc
Vehicle fit
Wide universal
Check price on Amazon
Extension rod included
#2
Yuesstloo GJ-134

Yuesstloo GJ-134Yuesstloo 11-Piece CV Axle Removal Kit

The only product here that lists an extension rod, plus a 63 mm fork and outer CV adapter.

Tool type
Multi-tool set
Pieces included
11 pc
Vehicle fit
Wide universal
Check price on Amazon
Pry option for FWD
#3
Bonbo VOL358

Bonbo VOL358Bonbo Axle Popper Kit 2-Piece

A two-piece popper kit for front-wheel-drive axles, with no slide hammer.

Tool type
Popper or pry tool
Pieces included
2 pc
Vehicle fit
Most FWD vehicles
Check price on Amazon

Comparison table

Swipe or scroll sideways to see every model.
Top 6 drive shaft removal tools
Spec
#1
DPTOOL L9110
Best overallCheck price on Amazon
#2
Yuesstloo GJ-134
Extension rod includedCheck price on Amazon
#3
Bonbo VOL358
Pry option for FWDCheck price on Amazon
#4
ReluxGo BJS054
63 mm fork, 3.3 in deepCheck price on Amazon
#5
P Polerden DT-51329-A
Narrow Chevrolet snap ring adapterCheck price on Amazon
#6
SCBoutique SCB-YXMTXCV-260603002
Check price on Amazon
Best Scoreout of 100847946392260
Tool typeMulti-tool set (best in row)Multi-tool set (best in row)Popper or pry toolFork or adapter onlyFork or adapter onlyMulti-tool set (best in row)
Pieces includedpc18 pc (best in row)11 pc2 pc1 pc1 pc8 pc
Slide hammer includedYes (best in row)Yes (best in row)NoNoNoYes (best in row)
Slide hammer weightlb10.5 lb————10.5 lb
Largest fork openingmm63 mm63 mm—63 mm—63 mm
Fork depthin———3.3 in——
Slide hammer threadM18 coarse threads——5/8"-18——
MaterialOther—Forged steel (best in row)Carbon steel—Forged steel (best in row)
Vehicle fitWide universal (best in row)Wide universal (best in row)Most FWD vehiclesSpecific models onlySpecific models onlyMost FWD vehicles
Extension rod included—Yes (best in row)NoNoNo—
Outer CV adapter includedYes (best in row)Yes (best in row)NoNoNo—
Storage case includedYes————Yes
Total weightlb————2.2 lb—
Best in row— not published by the maker yet

How we chose

We reviewed 15 drive shaft removal tools and kept only the 6 that pass every check below. Those are ranked by a Best Score built from spec fit for this job, sales rank.

Read the full method

In-depth reviews

These reviews are based on specifications and listing information. Each one explains what the specs mean for pulling a stuck shaft.

Best overall

DPTOOL L9110DPTOOL CV Axle Puller Slide Hammer Kit

Widest kit with a heavy slide hammer and case

Tool type
Multi-tool set (best of the reviewed tools)
Pieces included
18 pc (best of the reviewed tools)
Largest fork opening
63 mm (best of the reviewed tools)
Vehicle fit
Wide universal (best of the reviewed tools)

The DPTOOL L9110 is an 18-piece multi-tool set, and that is the highest piece count of the five products on this page. It includes a 10.5 lb slide hammer with M18 coarse threads. The slide hammer does the pulling, so a heavier one gives you more force on each strike against a stuck inner CV joint.

Two forks come in the kit, with openings of 48 mm and 63 mm. Fork size must match the joint housing, so two sizes cover more vehicles. The listing also names an outer CV adapter, a steel cable adapter, a 24 in breaker bar and a pry bar adapter head. The vehicle fit is listed as wide universal.

A plastic storage box holds the parts together. The material field reads Other, so the heavy duty steel claim rests on the listing text alone. Confirm the inner joint on your shaft is reachable by a fork before you buy.

Pros

  • 18 pieces, highest count
  • 10.5 lb slide hammer
  • Two forks and outer CV adapter

Cons

  • Material listed only as Other
  • Many parts you may not need
Buy it if
you want one kit for several vehicles.
Skip it if
you only need a single fork size.

VerdictThis kit leads our ranking because it pairs a heavy slide hammer with two fork sizes, an outer CV adapter and a case.

Extension rod included

Yuesstloo GJ-134Yuesstloo 11-Piece CV Axle Removal Kit

Compact 11-piece kit with an extension rod

Tool type
Multi-tool set (best of the reviewed tools)
Pieces included
11 pc
Largest fork opening
63 mm (best of the reviewed tools)
Vehicle fit
Wide universal (best of the reviewed tools)

The Yuesstloo GJ-134 is an 11-piece multi-tool set built around a slide hammer. The maker does not publish the slide hammer weight, so you cannot compare its pulling mass to the DPTOOL set. The listing calls it heavy duty and mentions a curved handle with a large surface for a more comfortable grip.

The kit has a 63 mm fork and a 48 mm fork, plus a second 63 mm fork listed as a new CV joint fork. An extension rod is included, which helps in tight spots where the hammer needs more reach. An outer CV adapter and a steel cable adapter are also in the kit.

Vehicle fit is listed as wide universal. Among the five products here, it is the only one that lists an extension rod as included. Both forks have internal threads that fit the external threads on the slide hammer rod. The listing does not mention a storage case, and the spec data gives no material.

Pros

  • 11 pieces with extension rod
  • 63 mm and 48 mm forks
  • Outer CV adapter included

Cons

  • Slide hammer weight not published
  • No storage case listed
Buy it if
you work in tight, hard-to-reach spots.
Skip it if
you need a case or a known hammer weight.

VerdictIt ranks second, a capable set with an extension rod, though it gives fewer specs than the DPTOOL kit.

Pry option for FWD

Bonbo VOL358Bonbo Axle Popper Kit 2-Piece

Simple pry tool for popping FWD axles loose

Tool type
Popper or pry tool
Pieces included
2 pc
Largest fork opening
—
Vehicle fit
Most FWD vehicles

The Bonbo VOL358 is a two-piece popper kit, not a puller. It has no slide hammer, no extension rod and no outer CV adapter. It works by prying the axle out of the transaxle with wedges, so it suits a different job than the slide hammer kits ranked above it.

The listing says you place the wedge between the transaxle housing and the shaft joint, with the fork end around the shaft. Then you tap the fork end to loosen the half shaft. The fork shape applies even pressure on both sides of the half shaft, per the listing. The wedges start at a depth of 1/4 in, which helps in tight spaces.

Material is forged steel, and the fit is listed as most FWD vehicles. A second piece, a dummy gasket fork, fills larger gaps on some vehicles. If a shaft will not move with prying alone, this kit has no pulling tool to fall back on.

Pros

  • Forged steel construction
  • Fits most FWD vehicles
  • Two pieces, simple to use

Cons

  • No slide hammer included
  • Pries only, cannot pull
Buy it if
you need to pop an axle out of a transaxle.
Skip it if
you need a true puller for stuck shafts.

VerdictIt ranks third and suits quick pry jobs on front-wheel-drive cars, but it is not a full removal kit.

63 mm fork, 3.3 in deep

ReluxGo BJS054ReluxGo 63mm Inner CV Axle Puller

Single 63 mm fork for specific Ford models

Tool type
Fork or adapter only
Pieces included
1 pc
Largest fork opening
63 mm (best of the reviewed tools)
Vehicle fit
Specific models only

The ReluxGo BJS054 is one U-shaped fork and nothing else. The opening is 63 mm and the depth is 3.3 in. You need your own slide hammer with 5/8"-18 threads, because none is included. Without one, the fork cannot pull anything. That is the main thing to check before you buy.

Depth matters because the fork must reach behind the inner boot and hook the joint housing. The 3.3 in depth is meant to pull joints with hidden retaining rings. The listing says it serves the wide-style inner CV joint assembly found on 4WD and other vehicles.

Fit is listed as specific models only. The examples named are 1997-2017 Ford models with 4.2L, 4.6L or 5.4L engines, the 2010-2014 Ford SVT Raptor, and the 2007-2015 Lincoln Navigator. Check the engine and year against the list before you order. The fork is carbon steel and heat-treated.

Pros

  • 63 mm opening, 3.3 in depth
  • Carbon steel, heat-treated
  • Named Ford and Lincoln fits

Cons

  • No slide hammer included
  • Only fits specific models
Buy it if
you own a listed Ford and a matching slide hammer.
Skip it if
you want a complete kit for several vehicles.

VerdictIt ranks fourth and works only as an add-on for owners who already have a slide hammer and a listed vehicle.

Narrow Chevrolet snap ring adapter

P Polerden DT-51329-APolerden DT-51329-A Driveshaft Adapter

Narrow adapter for certain Chevrolet prop shafts

Tool type
Fork or adapter only
Pieces included
1 pc
Largest fork opening
—
Vehicle fit
Specific models only

The Polerden DT-51329-A is a one-piece adapter, not a general driveshaft removal kit. It is built for the retention clip on the PTU or RDM splined shaft. The listing names the Equinox, Terrain, XT5, Acadia and Envision prop shafts. If your vehicle is not one of those, it does not fit the job.

Its two halves tighten around the prop shaft and seat into the groove. You then attach a slide hammer to unseat the snap ring. The listing names the J-02619-A slide hammer, and it is not included. The listing gives a removal force of 2000 to 6000 N at 50 mm/min.

The tool weighs 2.2 lb. Piece count is one, tied with the ReluxGo fork for the lowest on the page. It does not fit the typical stuck half shaft job in the keyword. The listing says unapproved methods can damage the prop shaft, so use the adapter as described.

Pros

  • Targets the PTU or RDM clip
  • Weighs 2.2 lb
  • Named supported models

Cons

  • No slide hammer included
  • Very narrow vehicle fit
Buy it if
you own a listed Chevrolet model and need to free the snap ring.
Skip it if
you want a general half shaft puller.

VerdictIt ranks last for this keyword because it solves one narrow job, so only owners of the named models should consider it.

Best among the reviewed tools

Buying guide

Match the fork opening

The fork hooks behind the inner CV joint housing, so its opening must fit your joint. The kits here list 48 mm and 63 mm forks. A single 63 mm fork is only useful if your joint needs that size.

Check for a slide hammer

A slide hammer turns repeated strikes into a straight pull, which is gentler than prying on a stuck shaft. Only two of the five products include one. Forks and adapters sold alone need a hammer with matching threads, so check the thread size before ordering.

Confirm vehicle fit first

Wide universal kits cover many vehicles, but a specific-fit adapter only works on the models it names. Read the application list and match your year, engine and shaft type. A tool that fits almost right can mar splines or seals.

Pullers versus pry tools

Popper tools pry the shaft out of the transaxle. Pullers use a slide hammer to draw it straight out. Prying can work when the shaft is clipped in and not seized. For a stubborn shaft, a puller kit gives you more ways to apply force.

FAQ

Do I need a slide hammer to remove a half shaft?

Often yes. A slide hammer pulls the inner joint out in a straight line. Some shafts pop out with a pry tool alone. Of the five products here, two include a slide hammer, and the ReluxGo and Polerden items need one you supply.

What fork size do I need for an inner CV joint?

It depends on the joint housing. The two kits here list 48 mm and 63 mm openings. The ReluxGo fork is 63 mm with a 3.3 in depth. Check your vehicle's application details before ordering, because size alone does not prove fit.

Will a universal kit fit my vehicle?

Two kits here list wide universal fit, and their listings say they suit most mainstream cars. Fit still depends on your joint design. Compare the fork openings to your joint and confirm your shaft is a type the kit covers.

Can I damage the seal or splines when removing a shaft?

Yes, if you force it. Pulling straight with a matching fork reduces the risk. Hammering or prying with the wrong tool can deform parts. Use the correct adapter, pull in line with the shaft and follow the instructions for your vehicle.

Related comparisons

Share this comparison

Your own selection is kept in the link, so friends see the same side-by-side.

Top pick · #1DPTOOL L9110
Check price on Amazon