Best Cabinet Pulls in 2027

Start with the hole spacing. These pulls use 3 in center-to-center spacing, which ties for the lowest among the models that list it. If your existing holes measure 3 in, these fit without new drilling. Overall length is 5 in, so each handle reaches past the holes on both sides and gives your fingers room.

The pack holds 30 pulls, which ties for the highest pack count on the page. That is enough for a large set of doors and drawers. The material is stainless steel in Matte Black, with 1.25 in of projection from the cabinet. The maker does not state a finish durability claim, so wear resistance is not documented in the data.

Listed weight is 3.22 lb. The listing offers a 365-Day Evaluation. Mounting screws are not confirmed in the data, so check the listing before you order. Pair these with matte black hardware elsewhere in the room for a matched look.

Measure first. These pulls need 5 in center-to-center spacing, so they suit larger drawers and doors drilled for that size. They will not fit 3 in holes. Overall length is 5.5 in, which gives a long grip across a wide drawer front. The listing also says the bar is 1/2 in wide and 1/2 in thick.

Projection is 1.4 in, the highest among the six models that list it. That means more room for your fingers behind the bar. Weight is 4.4 lb, the highest among the models that list weight. The pack holds 30 pulls and includes mounting screws. That ties for the highest pack count on the page.

Material is stainless steel in Matte Black, and no finish durability claim is listed. The 365-Day Evaluation in the listing gives a full year to decide if you like the finish. Keep the packaging until you are sure of the fit.

This is a round knob, not a pull. A knob sits on a single hole, so there is no hole spacing to match. The data lists no center-to-center spacing. If your drawers are drilled for two-hole pulls, these will not fit without new holes. Use them where a single hole already exists. Measure your existing holes before ordering.

Size is small. The listing gives a diameter of 1.18 in (30 mm) and a height of 7/8 in (22 mm). Overall length in the data is 1.25 in. The center is slightly concave, which the listing says gives a secure grip. Each knob comes with two screw sizes, 20 mm and 45 mm, to suit different panel thicknesses.

The pack holds 18 knobs in White stainless steel, with a listed weight of 0.71 lb. The maker states no finish durability claim, so wear on the white finish is not documented. Mounting screws are included. The listing says it suits bookcases, wardrobes, dressers and kitchen drawers.

This set matches the size of the top-ranked Ravinte but uses Satin Nickel instead of Matte Black. Spacing is 3 in center-to-center, overall length is 5 in, and projection is 1.25 in. If you are replacing old 3 in pulls, the dimensions line up without new holes. That keeps the swap simple.

Satin nickel suits kitchens with nickel appliances, and the listing makes that point directly. The bars are 1/2 in in diameter. Weight is listed at 3.15 lb, a little less than the matte black version at 3.22 lb. The pack of 30 matches the largest count on the page. That suits a full run of cabinets.

The material is stainless steel, and the finish durability claim is not stated. The data does not confirm mounting screws, so check before ordering. A 365-Day Evaluation is offered in the listing. It ranks fourth on our list, behind two other Ravinte sets and a white knob set.

Corrosion is a key worry for daily-use pulls, and this listing speaks to it. It says the stainless steel is hollow but durable and hard to get rusty. That is a maker statement, not a rating. The finish durability claim itself is listed as not stated.

Dimensions are 3 in center-to-center and 5 in overall length. Projection is not listed, so check clearance if your drawers sit close to other hardware. Weight is listed at 1.45 lb, and the listing describes a hollow build. The pack holds 15 pulls, half the count of the 30-piece Ravinte sets.

The set includes 1 in (25 mm) and 1.57 in (40 mm) screws for different board thicknesses. Check your door thickness against both lengths before you drill. The listing also says the arc is round with no corners, which the maker ties to fewer bumps for children. It ranks fifth on our list.